CMM/VMM

255 topics in this forum

1. Polyworks configuration

   By [An...] , February 14, 2024
   • 1 reply
   • 283 views
   • 
   • [An...]
   • March 7, 2024

2. "ID chip 481 error" System window error

   By [Ka...] , June 27, 2022
   • 3 replies
   • 240 views
   • 
   • [An...]
   • March 6, 2024

3. Probe pressure on the part

   By [Ma...] , November 8, 2023
   • 7 replies
   • 385 views
   • 
   • [Je...]
   • February 7, 2024

4. Air Pressure for a Zeiss Contura 9/18/6

   By [Jo...] , September 26, 2022
   • 6 replies
   • 518 views
   • 
   • [To...]
   • February 7, 2024

5. Question regarding Viscan - error.

   By [Ra...] , December 7, 2023
   • 1 reply
   • 213 views
   • 
   • [No...]
   • December 8, 2023

6. Z Release button on a Contura

   By [An...] , November 21, 2023
   • 11 replies
   • 566 views
   • 
   • [An...]
   • December 1, 2023

7. RDS Sensor Change

   By [To...] , November 9, 2023
   • 1 reply
   • 225 views
   • 
   • [Je...]
   • November 13, 2023

8. Recommended Settings for 0.100mm probe calibration?

   By [Sc...] , October 25, 2023
   • 3 replies
   • 370 views
   • 
   • [Ke...]
   • October 27, 2023

9. Older Vista CMM Drives wont turn on now?

   By [Wa...] , October 23, 2023
   • 4 replies
   • 324 views
   • 
   • [Wa...]
   • October 23, 2023

10. Reference plate

    By [Da...] , October 20, 2023
    • 4 replies
    • 209 views
    • 
    • [Th...]
    • October 23, 2023

11. Probe Calibration Accuracy

    By [Ch...] , October 17, 2023
    • 4 replies
    • 436 views
    • 
    • [Je...]
    • October 18, 2023

12. Adapter plates

    By [Se...] , August 1, 2023
    • 5 replies
    • 226 views
    • 
    • [Se...]
    • August 1, 2023

13. Contura VAST XT head not locking in probes after Zeiss Calibration

    By [Ja...] , July 11, 2023
    • 1 reply
    • 252 views
    • 
    • [Je...]
    • July 17, 2023

14. "Der Sensor hat die Messung nicht mit der erwarteten Tastkraft ausgeführt"

    By [Je...] , June 30, 2023
    • 10 replies
    • 401 views
    • 
    • [Je...]
    • July 7, 2023

15. CMM to CMM Variability

    By [Pr...] , June 15, 2023
    • 4 replies
    • 323 views
    • 
    • [Je...]
    • June 29, 2023

16. Torque value for head screw

    By [ke...] , June 8, 2023
    • 3 replies
    • 211 views
    • 
    • [ke...]
    • June 8, 2023

17. retainer rings for joystick buttons

    By [Da...] , May 25, 2023
    • 1 reply
    • 200 views
    • 
    • [Ke...]
    • May 25, 2023

18. VAST probing Erfahrungen

    By [Je...] , May 23, 2023
    • 0 replies
    • 173 views
    • 
    • [Je...]
    • May 23, 2023

19. OI-322

    By [Mi...] , April 26, 2023
    • 1 reply
    • 214 views
    • 
    • [Da...]
    • April 28, 2023

20. XXT Stylus Will Not Release

    By [Da...] , April 20, 2023
    • 2 replies
    • 235 views
    • 
    • [Er...]
    • April 24, 2023

21. Moving Probe Rack - Zeiss Accura

    By [Ja...] , February 9, 2023
    • 4 replies
    • 237 views
    • 
    • [Ja...]
    • April 3, 2023

22. CMM Calibration

    By [Jo...] , March 15, 2023
    • 6 replies
    • 253 views
    • 
    • [Jo...]
    • March 28, 2023

23. Use Offline Laptop to run CMM

    By [Ri...] , March 14, 2023
    • 3 replies
    • 210 views
    • 
    • [No...]
    • March 15, 2023

24. Disappearing Holder Locations

    By [Ma...] , March 8, 2023
    • 6 replies
    • 230 views
    • 
    • [No...]
    • March 10, 2023

25. Low Temperature..

    By [Ya...] , February 27, 2023
    • 2 replies
    • 286 views
    • 
    • [Ke...]
    • February 27, 2023