Optical 3D

211 topics in this forum

1. Low quality of triple scan points error

   By [Sh...] , May 7, 2025
   • 9 replies
   • 2.6k views
   • 
   • [Je...]
   • June 16, 2025

2. How to activate license and start INSPECT Optical 3D on offline PC ?

   By [Ka...] , May 28, 2025
   • 1 reply
   • 1.3k views
   • 
   • [Je...]
   • June 12, 2025

3. Mit welchen Messsystemen kann Inspect messen

   By [Ax...] , April 4, 2025
   • 2 replies
   • 1.9k views
   • 
   • [Ax...]
   • May 15, 2025

4. Zeiss Comet L3D 5M - installation issue - Gig E vision board not found

   By [Lu...] , March 26, 2024
   • 4 replies
   • 3.5k views
   • 
   • [Ab...]
   • April 22, 2025

5. T-hawk 2 scanner will not initialize scan lines

   By [mi...] , December 4, 2024
   • 1 reply
   • 2.1k views
   • 
   • [Ky...]
   • April 16, 2025

6. Losing detail on vane leading and trailing edges after polygonization

   By [Mi...] , April 11, 2025
   • 1 reply
   • 2.2k views
   • 
   • [Ch...]
   • April 15, 2025

7. T-Hawk 2 not supported by Zeiss Inspect 2025?

   By [Se...] , April 9, 2025
   • 1 reply
   • 1.1k views
   • 
   • [Na...]
   • April 9, 2025

8. Reliability of Hyperscale calibration with ATOS Q

   By [Yu...] , April 9, 2025
   • 0 replies
   • 1.3k views
   • 
   • [Yu...]
   • April 9, 2025

9. Inspect Correlate 2023 - Getting extremely slow when adding multiple measurement series

   By [Ch...] , April 3, 2025
   • 1 reply
   • 1.2k views
   • 
   • [Ch...]
   • April 3, 2025

10. Notebook for data acquisition

    By [Ma...] , September 26, 2024
    • 3 replies
    • 2.7k views
    • 
    • [Ky...]
    • April 2, 2025

11. Best way to measure threaded holes?

    By [da...] , March 14, 2025
    • 2 replies
    • 3.5k views
    • 
    • [da...]
    • March 21, 2025

12. Compact Scan Error 1282

    By [St...] , September 3, 2021
    • 9 replies
    • 7.7k views
    • 
    • [Ja...]
    • March 14, 2025

13. Need help PMI - import to Inspect optical 3D. - show invalid or not support.

    By [Yo...] , February 28, 2025
    • 1 reply
    • 790 views
    • 
    • [na...]
    • March 3, 2025

14. ATOS I 2M 350 scanning size issue

    By [Et...] , December 27, 2024
    • 3 replies
    • 2k views
    • 
    • [Ja...]
    • February 18, 2025

15. Triggering Scan Directly in ZEISS HAWK2 ADD-ON

    By [Yu...] , February 10, 2025
    • 0 replies
    • 1.1k views
    • 
    • [Yu...]
    • February 10, 2025

16. Free ZEISS INSPECT Optical 3D

    By [Je...] , January 14, 2025
    • 2 replies
    • 1.9k views
    • 
    • [Mi...]
    • February 4, 2025

17. Error MPROJ-0040 T-Scan hawk 2

    By [Zu...] , January 25, 2024
    • 4 replies
    • 11.7k views
    • 
    • [Mi...]
    • February 4, 2025

18. Is it possible to extract raw CT scan data from a GOM Inspect file?

    By [Fi...] , January 22, 2024
    • 1 reply
    • 2.7k views
    • 
    • [Ra...]
    • January 30, 2025

19. Use of Track Ball mouse instead of Logitech R400 remote control for ATOS scan

    By [Sh...] , February 20, 2024
    • 1 reply
    • 1.8k views
    • 
    • [Ra...]
    • January 30, 2025

20. Save scan images

    By [Ri...] , March 13, 2024
    • 1 reply
    • 6.6k views
    • 
    • [Ra...]
    • January 30, 2025

21. Changing to smaller Measuring Volumes (MV)

    By [Iv...] , September 20, 2024
    • 1 reply
    • 1.6k views
    • 
    • [Ra...]
    • January 30, 2025

22. Ausrichtung der Messungen

    By [Ja...] , September 13, 2024
    • 6 replies
    • 2.4k views
    • 
    • [Ja...]
    • January 29, 2025

23. Verschiedene Scanbereiche trotz gleicher Vorlage

    By [Ja...] , January 29, 2025
    • 0 replies
    • 676 views
    • 
    • [Ja...]
    • January 29, 2025

24. ARAMIS adjustable "only 1 camera was found"

    By [Ma...] , July 22, 2024
    • 2 replies
    • 1.6k views
    • 
    • [Ma...]
    • January 28, 2025

25. Punkt zur Ausrichtung zustellen

    By [Th...] , January 23, 2025
    • 0 replies
    • 6.7k views
    • 
    • [Th...]
    • January 23, 2025