General

8148 topics in this forum

1. Moving Contura G2 Vast XT

   By [Sc...] , December 16, 2022
   • 5 replies
   • 1.4k views
   • 
   • [Sc...]
   • January 12, 2024

2. Output last characteristic after measuring with loop and offse

   By [Wi...] , January 12, 2024
   • 1 reply
   • 570 views
   • 
   • [Ma...]
   • January 12, 2024

3. Upgrading from calypso 5.4 to the latest version

   By [Ma...] , January 10, 2024
   • 8 replies
   • 3.9k views
   • 
   • [No...]
   • January 11, 2024

4. Cylindricity of .0003"

   By [Li...] , December 19, 2023
   • 14 replies
   • 2k views
   • 
   • [Tr...]
   • January 10, 2024

5. Combine Header and Characteristics At .txt Report

   By [Za...] , December 18, 2023
   • 12 replies
   • 1.5k views
   • 
   • [An...]
   • January 10, 2024

6. Contura Y Antrieb Konstruktionsfehler?

   By [Ba...] , January 8, 2024
   • 4 replies
   • 620 views
   • 
   • [Ba...]
   • January 10, 2024

7. Edit default warm-up program? (is it a macro?)

   By [Mi...] , January 9, 2024
   • 4 replies
   • 1.2k views
   • 
   • [No...]
   • January 10, 2024

8. Skipping Yearly Calibration

   By [Ni...] , January 9, 2024
   • 1 reply
   • 600 views
   • 
   • [Cl...]
   • January 9, 2024

9. Need help aligning a ring with flats on the ID

   By [Gr...] , January 4, 2024
   • 4 replies
   • 874 views
   • 
   • [Ni...]
   • January 9, 2024

10. Cumulative runout lower than runout?

    By [Co...] , January 8, 2024
    • 2 replies
    • 952 views
    • 
    • [Ow...]
    • January 9, 2024

11. PCM appending results

    By [Cl...] , January 9, 2024
    • 1 reply
    • 591 views
    • 
    • [Ch...]
    • January 9, 2024

12. Vorrichtung: Spannhilfe prüfen

    By [Ka...] , January 5, 2024
    • 7 replies
    • 923 views
    • 
    • [Ha...]
    • January 9, 2024

13. Actual vs Nominal

    By [Cl...] , January 3, 2024
    • 14 replies
    • 2.2k views
    • 
    • [No...]
    • January 9, 2024

14. Seeking Assistance with Zeiss Calypso Software - Thickness Measurement Discrepancies

    By [St...] , January 8, 2024
    • 5 replies
    • 1.5k views
    • 
    • [Ri...]
    • January 8, 2024

15. PMC Formel entfernen ohne PCM Funktion?

    By [Sa...] , January 8, 2024
    • 1 reply
    • 474 views
    • 
    • [No...]
    • January 8, 2024

16. Manually change adapter plates

    By [Sc...] , December 21, 2023
    • 4 replies
    • 867 views
    • 
    • [No...]
    • January 8, 2024

17. Corrupted CAD entity

    By [Cl...] , December 29, 2023
    • 2 replies
    • 529 views
    • 
    • [Cl...]
    • January 5, 2024

18. Cylinder(Mutiple circles path) diameter results

    By [Sc...] , January 3, 2024
    • 6 replies
    • 1.4k views
    • 
    • [Da...]
    • January 4, 2024

19. Install Calypso 7.4, use Dongle/Lincense from another install?

    By [Ri...] , January 4, 2024
    • 2 replies
    • 1.2k views
    • 
    • [Ri...]
    • January 4, 2024

20. Part alignment vs physical orientation

    By [St...] , January 2, 2024
    • 5 replies
    • 893 views
    • 
    • [Ma...]
    • January 2, 2024

21. Darstellung von Bezügen mit Zusatz ><

    By [Mi...] , January 2, 2024
    • 2 replies
    • 807 views
    • 
    • [Ma...]
    • January 2, 2024

22. Profile question

    By [Ma...] , December 18, 2023
    • 3 replies
    • 633 views
    • 
    • [Ri...]
    • January 2, 2024

23. Disabling Clearance Move

    By [An...] , December 27, 2023
    • 9 replies
    • 1.4k views
    • 
    • [An...]
    • December 29, 2023

24. True position producing smaller diameter

    By [Ch...] , December 27, 2023
    • 5 replies
    • 1k views
    • 
    • [Mi...]
    • December 27, 2023

25. Christmas

    By [Cl...] , December 22, 2023
    • 4 replies
    • 671 views
    • 
    • [Ke...]
    • December 26, 2023