General

8326 topics in this forum

1. Calypso 2027 1 2 3

   By [Ch...] , October 20
   • 64 replies
   • 2.8k views
   • 
   • [Ro...]
   • 38 minutes ago

2. Micura - Can't enable drives.

   By [Gr...] , October 26
   • 7 replies
   • 330 views
   • 
   • [Ch...]
   • 2 hours ago

3. Base/startsystem setup

   By [Ni...] , November 4
   • 11 replies
   • 420 views
   • 
   • [Ni...]
   • 11 hours ago

4. Curve vs FF

   By [Da...] , November 4
   • 6 replies
   • 283 views
   • 
   • [Je...]
   • 13 hours ago

5. MMC data not present after results to file operation

   By [D...] , 20 hours ago
   • 0 replies
   • 50 views
   • 
   • [D...]
   • 20 hours ago

6. Calibration Results

   By [Da...] , May 15
   • 5 replies
   • 795 views
   • 
   • [Ma...]
   • Yesterday at 01:50 PM

7. Measuring runout of a torus

   By [Ro...] , Friday at 09:13 PM
   • 5 replies
   • 178 views
   • 
   • [Wo...]
   • Monday at 11:31 PM

8. O-Inspect + Calypso 2027

   By [Ca...] , Saturday at 07:26 PM
   • 1 reply
   • 192 views
   • 
   • [No...]
   • Monday at 07:29 AM

9. Maximum Linear Distance

   By [St...] , Friday at 12:46 PM
   • 1 reply
   • 146 views
   • 
   • [Ma...]
   • Friday at 01:29 PM

10. Ref Sphere

    By [Mi...] , November 5
    • 9 replies
    • 241 views
    • 
    • [Ri...]
    • Friday at 11:53 AM

11. Loop in program.

    By [Ma...] , Friday at 08:59 AM
    • 3 replies
    • 155 views
    • 
    • [Ma...]
    • Friday at 09:44 AM

12. Qualification Program with RDS-CAA probe

    By [Da...] , Thursday at 10:53 PM
    • 0 replies
    • 111 views
    • 
    • [Da...]
    • Thursday at 10:53 PM

13. CAA probe calibration magic

    By [Be...] , Thursday at 10:26 PM
    • 0 replies
    • 107 views
    • 
    • [Be...]
    • Thursday at 10:26 PM

14. Calibration Results

    By [Ba...] , November 3
    • 8 replies
    • 269 views
    • 
    • [No...]
    • November 4

15. Easiest way to CMM settings to a newer version

    By [Jo...] , November 3
    • 5 replies
    • 272 views
    • 
    • [No...]
    • November 4

16. Radius measurement with small arc

    By [Ba...] , October 20
    • 9 replies
    • 636 views
    • 
    • [Ze...]
    • November 3

17. 2018 Calypso 6.6 install on new Win 11 machine

    By [Ra...] , October 1, 2025
    • 9 replies
    • 2k views
    • 
    • [An...]
    • November 3

18. Change Segment in 3-D scan

    By [Ke...] , November 2
    • 2 replies
    • 172 views
    • 
    • [Cr...]
    • November 3

19. How to fully measure inner thread like M22 6H

    By [Ma...] , October 29
    • 12 replies
    • 470 views
    • 
    • [Ma...]
    • November 3

20. Cad Model Assembly

    By [Ra...] , November 2
    • 4 replies
    • 248 views
    • 
    • [Lu...]
    • November 3

21. How define an plate stylus in Stylus-Kit Software

    By [Ka...] , October 30
    • 6 replies
    • 272 views
    • 
    • [Lu...]
    • November 2

22. Alignment vs. individual features

    By [Li...] , October 30
    • 3 replies
    • 431 views
    • 
    • [Jo...]
    • November 2

23. probe orientation numbers

    By [Be...] , October 30
    • 4 replies
    • 250 views
    • 
    • [Ri...]
    • November 2

24. calibrating angle probe

    By [ch...] , February 5, 2020
    • 9 replies
    • 1.7k views
    • 
    • [Be...]
    • October 30

25. profile, simultaneous requirement

    By [To...] , October 30
    • 9 replies
    • 392 views
    • 
    • [To...]
    • October 30