General

7071 topics in this forum

1. Turn off CAD redraw?

   By [Ri...] , January 8, 2024
   • 4 replies
   • 74 views
   • 
   • [Ri...]
   • January 12, 2024

2. Abfrage ob Spanner/Ausrichtblock entfernt wurde

   By [P....] , January 12, 2024
   • 3 replies
   • 105 views
   • 
   • [P....]
   • January 12, 2024

3. Angle on a Helix

   By [Ty...] , January 9, 2024
   • 7 replies
   • 157 views
   • 
   • [Da...]
   • January 12, 2024

4. Moving Contura G2 Vast XT

   By [Sc...] , December 16, 2022
   • 5 replies
   • 108 views
   • 
   • [Sc...]
   • January 12, 2024

5. Output last characteristic after measuring with loop and offse

   By [Wi...] , January 12, 2024
   • 1 reply
   • 61 views
   • 
   • [Ma...]
   • January 12, 2024

6. Upgrading from calypso 5.4 to the latest version

   By [Ma...] , January 10, 2024
   • 8 replies
   • 110 views
   • 
   • [No...]
   • January 11, 2024

7. Cylindricity of .0003"

   By [Li...] , December 19, 2023
   • 14 replies
   • 118 views
   • 
   • [Tr...]
   • January 10, 2024

8. Combine Header and Characteristics At .txt Report

   By [Za...] , December 18, 2023
   • 12 replies
   • 83 views
   • 
   • [An...]
   • January 10, 2024

9. Contura Y Antrieb Konstruktionsfehler?

   By [P....] , January 8, 2024
   • 4 replies
   • 74 views
   • 
   • [P....]
   • January 10, 2024

10. Edit default warm-up program? (is it a macro?)

    By [Mi...] , January 9, 2024
    • 4 replies
    • 97 views
    • 
    • [No...]
    • January 10, 2024

11. Skipping Yearly Calibration

    By [Ni...] , January 9, 2024
    • 1 reply
    • 67 views
    • 
    • [Cl...]
    • January 9, 2024

12. Need help aligning a ring with flats on the ID

    By [Gr...] , January 4, 2024
    • 4 replies
    • 77 views
    • 
    • [Ni...]
    • January 9, 2024

13. Cumulative runout lower than runout?

    By [Co...] , January 8, 2024
    • 2 replies
    • 100 views
    • 
    • [Ow...]
    • January 9, 2024

14. PCM appending results

    By [Cl...] , January 9, 2024
    • 1 reply
    • 70 views
    • 
    • [Ch...]
    • January 9, 2024

15. Vorrichtung: Spannhilfe prüfen

    By [Ka...] , January 5, 2024
    • 7 replies
    • 95 views
    • 
    • [Ha...]
    • January 9, 2024

16. Actual vs Nominal

    By [Cl...] , January 3, 2024
    • 14 replies
    • 141 views
    • 
    • [No...]
    • January 9, 2024

17. Seeking Assistance with Zeiss Calypso Software - Thickness Measurement Discrepancies

    By [St...] , January 8, 2024
    • 5 replies
    • 143 views
    • 
    • [Ri...]
    • January 8, 2024

18. PMC Formel entfernen ohne PCM Funktion?

    By [Sa...] , January 8, 2024
    • 1 reply
    • 63 views
    • 
    • [No...]
    • January 8, 2024

19. Manually change adapter plates

    By [Sc...] , December 21, 2023
    • 4 replies
    • 80 views
    • 
    • [No...]
    • January 8, 2024

20. Corrupted CAD entity

    By [Cl...] , December 29, 2023
    • 2 replies
    • 81 views
    • 
    • [Cl...]
    • January 5, 2024

21. Cylinder(Mutiple circles path) diameter results

    By [Sc...] , January 3, 2024
    • 6 replies
    • 95 views
    • 
    • [Da...]
    • January 4, 2024

22. Install Calypso 7.4, use Dongle/Lincense from another install?

    By [Ri...] , January 4, 2024
    • 2 replies
    • 132 views
    • 
    • [Ri...]
    • January 4, 2024

23. Part alignment vs physical orientation

    By [St...] , January 2, 2024
    • 5 replies
    • 98 views
    • 
    • [Ma...]
    • January 2, 2024

24. Darstellung von Bezügen mit Zusatz ><

    By [Mi...] , January 2, 2024
    • 2 replies
    • 74 views
    • 
    • [Ma...]
    • January 2, 2024

25. Profile question

    By [Ma...] , December 18, 2023
    • 3 replies
    • 69 views
    • 
    • [Ri...]
    • January 2, 2024