3D Inspection & Mesh Editing​

890 topics in this forum

1. Spalt zwischen zwei Teilen visualisieren

   By [Jö...] , March 22, 2023
   • 3 replies
   • 2.3k views
   • 
   • [Jö...]
   • March 28, 2023

2. Angle of a cone "units"

   By [Kl...] , March 8, 2023
   • 1 reply
   • 9.2k views
   • 
   • [Je...]
   • March 20, 2023

3. MMC on Composite Tolerances

   By [Ry...] , March 1, 2023
   • 6 replies
   • 6.7k views
   • 
   • [Ti...]
   • March 18, 2023

4. export quality of inspection sections

   By [Fa...] , March 15, 2023
   • 2 replies
   • 2.7k views
   • 
   • [Je...]
   • March 16, 2023

5. Creating Offset Planes

   By [Ja...] , March 15, 2023
   • 2 replies
   • 6.5k views
   • 
   • [Na...]
   • March 16, 2023

6. Inclined tolerance zone - request for opinion

   By [Ma...] , March 15, 2023
   • 0 replies
   • 3.8k views
   • 
   • [Ma...]
   • March 15, 2023

7. Area not included in surface comparison

   By [Wo...] , February 27, 2023
   • 2 replies
   • 20.7k views
   • 
   • [No...]
   • March 10, 2023

8. (Help Needed) Decrease only on side of the borders when you calculate surface

   By [Vi...] , March 9, 2023
   • 1 reply
   • 2.4k views
   • 
   • [Na...]
   • March 9, 2023

9. Angle of a cone

   By [Ti...] , February 26, 2023
   • 4 replies
   • 7.6k views
   • 
   • [Ti...]
   • March 4, 2023

10. Schnittkreis in einem Rohrbogen Messen

    By [Th...] , February 17, 2023
    • 1 reply
    • 3.1k views
    • 
    • [Na...]
    • March 3, 2023

11. Auxiliary CAD Lines CALYPSO vs GOM

    By [Vi...] , February 28, 2023
    • 2 replies
    • 3.6k views
    • 
    • [Vi...]
    • March 1, 2023

12. Darstellung Schnittkurve und Linien / Representation of section curve and lines

    By [An...] , February 22, 2023
    • 2 replies
    • 2.3k views
    • 
    • [An...]
    • February 25, 2023

13. Inspecting Point Clouds

    By [Ad...] , February 16, 2023
    • 4 replies
    • 5.7k views
    • 
    • [Ad...]
    • February 23, 2023

14. Surface Comparison irregularities

    By [Ja...] , February 23, 2023
    • 3 replies
    • 18k views
    • 
    • [Ja...]
    • February 23, 2023

15. What is the standard referenced for Y14.5 Gaussian best fit OUTER plane in 2022 version? (and related questions)

    By [Ap...] , January 19, 2023
    • 7 replies
    • 4.9k views
    • 
    • [Ap...]
    • February 23, 2023

16. Section in relation to a plane

    By [Pi...] , February 13, 2023
    • 5 replies
    • 13.2k views
    • 
    • [Pi...]
    • February 15, 2023

17. Measure distance of plane

    By [Ry...] , January 24, 2023
    • 3 replies
    • 6.3k views
    • 
    • [Be...]
    • February 9, 2023

18. Messen eines Lochkreises in GOM Inspect 2020

    By [Jo...] , February 1, 2021
    • 7 replies
    • 7.3k views
    • 
    • [No...]
    • February 9, 2023

19. Feature size changes when using pre-alignment vs local alignment

    By [Ti...] , February 5, 2023
    • 4 replies
    • 3.6k views
    • 
    • [Ti...]
    • February 8, 2023

20. Local CAD comparison without sharp edges of Cad model

    By [Go...] , December 28, 2022
    • 7 replies
    • 12.1k views
    • 
    • [Mi...]
    • February 1, 2023

21. High Transformation Deviation

    By [Ga...] , January 26, 2023
    • 1 reply
    • 12.3k views
    • 
    • [Ja...]
    • January 26, 2023

22. How to evaluate diameter of circle on 3D mesh?

    By [ph...] , January 24, 2023
    • 2 replies
    • 3.1k views
    • 
    • [Na...]
    • January 25, 2023

23. How to measure to edge of cylinder/circle

    By [Ch...] , August 16, 2021
    • 3 replies
    • 14.5k views
    • 
    • [Ti...]
    • January 25, 2023

24. Unequal Grid Section Plots

    By [Je...] , January 14, 2023
    • 2 replies
    • 4k views
    • 
    • [Na...]
    • January 19, 2023

25. Ordnerstruktur Software 2021 / Reportvorlagen aktualisieren?

    By [Si...] , January 17, 2023
    • 1 reply
    • 5.2k views
    • 
    • [Na...]
    • January 19, 2023