3D Inspection & Mesh Editing​

883 topics in this forum

1. Trouble with mirroring features

   By [Ti...] , May 16, 2023
   • 5 replies
   • 7.7k views
   • 
   • [Ja...]
   • May 25, 2023

2. Kreis aus mehreren Zylindern

   By [Ad...] , May 24, 2023
   • 1 reply
   • 8.4k views
   • 
   • [Na...]
   • May 25, 2023

3. What does 'Compute additional best fit' do?

   By [Ti...] , May 20, 2023
   • 1 reply
   • 3.4k views
   • 
   • [Be...]
   • May 22, 2023

4. polygonisieren, automatisches selektieren mehrerer Bauteile

   By [Al...] , May 16, 2023
   • 1 reply
   • 1.8k views
   • 
   • [Be...]
   • May 16, 2023

5. Visualisierung ISO 3D

   By [Ju...] , May 5, 2023
   • 1 reply
   • 13.5k views
   • 
   • [Ch...]
   • May 8, 2023

6. MMC for a line - need to get linear size

   By [Ti...] , May 5, 2023
   • 2 replies
   • 3k views
   • 
   • [Ti...]
   • May 5, 2023

7. Einzelnes Abweichungsfähnchen wird als unbenutzter Werte angezeigt.

   By [St...] , April 3, 2023
   • 2 replies
   • 2.2k views
   • 
   • [St...]
   • May 3, 2023

8. Koordinaten von Zylindern anzeigen

   By [St...] , August 19, 2021
   • 7 replies
   • 14.5k views
   • 
   • [Ch...]
   • May 3, 2023

9. Error in 3D Calibration from image series

   By [mo...] , April 29, 2023
   • 1 reply
   • 3.2k views
   • 
   • [Na...]
   • May 2, 2023

10. Rename a check, e.g. “T” instead of “dN”

    By [Je...] , April 23, 2023
    • 1 reply
    • 2.9k views
    • 
    • [Je...]
    • April 25, 2023

11. Measuring GD&T to Datum System that is not fully constrained.

    By [le...] , April 18, 2023
    • 1 reply
    • 2.5k views
    • 
    • [Ch...]
    • April 19, 2023

12. Measuring Angle Between 2 Planes

    By [Jo...] , April 6, 2023
    • 1 reply
    • 5.5k views
    • 
    • [Ti...]
    • April 18, 2023

13. Position prüfen (mit CZ)

    By [Ch...] , March 30, 2023
    • 4 replies
    • 7.2k views
    • 
    • [Ch...]
    • April 12, 2023

14. hard to catch points when right angle has radius

    By [Th...] , April 5, 2023
    • 3 replies
    • 3.3k views
    • 
    • [Di...]
    • April 11, 2023

15. Which association criterion is used by GOM to find a datum line for a cylinder which covers less than 180°?

    By [Er...] , April 3, 2023
    • 3 replies
    • 3.1k views
    • 
    • [Ch...]
    • April 4, 2023

16. Automatically Recalculate doesn't work

    By [Ma...] , March 31, 2023
    • 5 replies
    • 5.5k views
    • 
    • [Be...]
    • April 3, 2023

17. how to meaure negative angle

    By [Ad...] , March 29, 2023
    • 2 replies
    • 12.8k views
    • 
    • [Ad...]
    • March 31, 2023

18. Measuring thickness of a clear part

    By [Jo...] , March 30, 2023
    • 1 reply
    • 6.1k views
    • 
    • [Ja...]
    • March 30, 2023

19. Spalt zwischen zwei Teilen visualisieren

    By [Jö...] , March 22, 2023
    • 3 replies
    • 2.3k views
    • 
    • [Jö...]
    • March 28, 2023

20. Angle of a cone "units"

    By [Kl...] , March 8, 2023
    • 1 reply
    • 9.1k views
    • 
    • [Je...]
    • March 20, 2023

21. MMC on Composite Tolerances

    By [Ry...] , March 1, 2023
    • 6 replies
    • 6.6k views
    • 
    • [Ti...]
    • March 18, 2023

22. export quality of inspection sections

    By [Fa...] , March 15, 2023
    • 2 replies
    • 2.7k views
    • 
    • [Je...]
    • March 16, 2023

23. Creating Offset Planes

    By [Ja...] , March 15, 2023
    • 2 replies
    • 6.5k views
    • 
    • [Na...]
    • March 16, 2023

24. Inclined tolerance zone - request for opinion

    By [Ma...] , March 15, 2023
    • 0 replies
    • 3.8k views
    • 
    • [Ma...]
    • March 15, 2023

25. Area not included in surface comparison

    By [Wo...] , February 27, 2023
    • 2 replies
    • 20.6k views
    • 
    • [No...]
    • March 10, 2023