3D Inspection & Mesh Editing​

880 topics in this forum

1. Max point on a section

   By [Ma...] , May 5, 2022
   • 3 replies
   • 11.3k views
   • 
   • [Be...]
   • May 9, 2022

2. How to export deviation labels

   By [Dr...] , May 2, 2022
   • 1 reply
   • 3.7k views
   • 
   • [Je...]
   • May 9, 2022

3. Correct way to recalculate preallignment with additional help point

   By [Ma...] , May 2, 2022
   • 1 reply
   • 2.4k views
   • 
   • [Je...]
   • May 9, 2022

4. distance check

   By [ey...] , May 8, 2022
   • 1 reply
   • 7.4k views
   • 
   • [Na...]
   • May 9, 2022

5. Differences between meshes in located points

   By [Ma...] , May 5, 2022
   • 1 reply
   • 4.6k views
   • 
   • [Be...]
   • May 6, 2022

6. Average gap value

   By [Jo...] , May 5, 2022
   • 2 replies
   • 20.4k views
   • 
   • [Jo...]
   • May 5, 2022

7. Ebene bilden aus mahr als 3 Fittingpunkten

   By [He...] , May 5, 2022
   • 4 replies
   • 3k views
   • 
   • [He...]
   • May 5, 2022

8. How to record/get current 3D view in Script

   By [Dr...] , May 2, 2022
   • 1 reply
   • 2.8k views
   • 
   • [Be...]
   • May 3, 2022

9. Flächenvergleich zeigt unplausible Werte trotz lokalem Bestfit

   By [No...] , May 2, 2022
   • 3 replies
   • 2.6k views
   • 
   • [Na...]
   • May 2, 2022

10. 2 points and use the one that it's the highest in a direction

    By [Ma...] , April 26, 2022
    • 7 replies
    • 3.8k views
    • 
    • [Be...]
    • May 2, 2022

11. automatic polygonize with scripts

    By [ey...] , April 26, 2022
    • 1 reply
    • 5.3k views
    • 
    • [Je...]
    • April 29, 2022

12. Developable surface

    By [be...] , April 27, 2022
    • 2 replies
    • 8.3k views
    • 
    • [be...]
    • April 28, 2022

13. Analysis of a cross section on CAD and actual data - Cross sectional area - GOM Inspect Pro

    By [Ca...] , April 27, 2022
    • 3 replies
    • 4.8k views
    • 
    • [Na...]
    • April 27, 2022

14. Material thickness comparison against nominal - GOM Inspect Pro

    By [Ca...] , April 27, 2022
    • 1 reply
    • 4.4k views
    • 
    • [Na...]
    • April 27, 2022

15. Zusätzliche Toleranzzonenrichtung bei Position mit CZ

    By [No...] , April 26, 2022
    • 4 replies
    • 3.2k views
    • 
    • [No...]
    • April 27, 2022

16. Anmerkung: Reportseitenbearbeitung weist oft Fehler auf - Version 2021 Hotfix 5 Rev.148065

    By [Ma...] , April 22, 2022
    • 2 replies
    • 2.7k views
    • 
    • [Ma...]
    • April 22, 2022

17. Export von konstruierten Geometrieelementen

    By [Ch...] , February 24, 2022
    • 2 replies
    • 4.8k views
    • 
    • [Ax...]
    • April 22, 2022

18. Position einer Ebene zu einem Zylinder prüfen

    By [Ax...] , April 7, 2022
    • 4 replies
    • 3.3k views
    • 
    • [Ax...]
    • April 21, 2022

19. Größe Flyer

    By [Fr...] , March 30, 2022
    • 3 replies
    • 2.8k views
    • 
    • [Na...]
    • April 12, 2022

20. Toleranzquelle

    By [St...] , April 11, 2022
    • 2 replies
    • 7.9k views
    • 
    • [St...]
    • April 11, 2022

21. Flächenprofil einer aufgeschäumten Dichtung

    By [No...] , April 8, 2022
    • 3 replies
    • 4.7k views
    • 
    • [Be...]
    • April 11, 2022

22. Best Fit Profile Min and Max Deviation points

    By [Le...] , April 5, 2022
    • 2 replies
    • 3k views
    • 
    • [Le...]
    • April 5, 2022

23. Circle Tangent 2 lines

    By [Ja...] , April 4, 2022
    • 2 replies
    • 13k views
    • 
    • [Ja...]
    • April 5, 2022

24. Flächenform Abweichung auf Patchbereich

    By [St...] , April 1, 2022
    • 6 replies
    • 3.7k views
    • 
    • [St...]
    • April 5, 2022

25. Was gibt die Messung "Flächenprofil messen" aus?

    By [Ta...] , March 30, 2022
    • 2 replies
    • 2.9k views
    • 
    • [Ta...]
    • March 30, 2022