Optical 3D

191 topics in this forum

1. Error MFG-0011

   By [Mi...] , June 16
   • 1 reply
   • 355 views
   • 
   • [Ja...]
   • June 20

2. Low quality of triple scan points error

   By [Sh...] , May 7
   • 9 replies
   • 717 views
   • 
   • [Je...]
   • June 16

3. How to activate license and start INSPECT Optical 3D on offline PC ?

   By [Ka...] , May 28
   • 1 reply
   • 292 views
   • 
   • [Je...]
   • June 12

4. Hardware Initialization failed

   By [ra...] , May 27
   • 0 replies
   • 308 views
   • 
   • [ra...]
   • May 27

5. Mit welchen Messsystemen kann Inspect messen

   By [Ax...] , April 4
   • 2 replies
   • 808 views
   • 
   • [Ax...]
   • May 15

6. Zeiss Comet L3D 5M - installation issue - Gig E vision board not found

   By [Lu...] , March 26, 2024
   • 4 replies
   • 1.8k views
   • 
   • [Ab...]
   • April 22

7. T-hawk 2 scanner will not initialize scan lines

   By [mi...] , December 4, 2024
   • 1 reply
   • 1.1k views
   • 
   • [Ky...]
   • April 16

8. Losing detail on vane leading and trailing edges after polygonization

   By [Mi...] , April 11
   • 1 reply
   • 1.4k views
   • 
   • [Ch...]
   • April 15

9. T-Hawk 2 not supported by Zeiss Inspect 2025?

   By [Se...] , April 9
   • 1 reply
   • 467 views
   • 
   • [Na...]
   • April 9

10. Reliability of Hyperscale calibration with ATOS Q

    By [Yu...] , April 9
    • 0 replies
    • 395 views
    • 
    • [Yu...]
    • April 9

11. Inspect Correlate 2023 - Getting extremely slow when adding multiple measurement series

    By [Ch...] , April 3
    • 1 reply
    • 381 views
    • 
    • [Ch...]
    • April 3

12. Notebook for data acquisition

    By [Ma...] , September 26, 2024
    • 3 replies
    • 1.7k views
    • 
    • [Ky...]
    • April 2

13. Best way to measure threaded holes?

    By [da...] , March 14
    • 2 replies
    • 2k views
    • 
    • [da...]
    • March 21

14. Compact Scan Error 1282

    By [St...] , September 3, 2021
    • 9 replies
    • 6.4k views
    • 
    • [Ja...]
    • March 14

15. Need help PMI - import to Inspect optical 3D. - show invalid or not support.

    By [Yo...] , February 28
    • 1 reply
    • 418 views
    • 
    • [na...]
    • March 3

16. ATOS I 2M 350 scanning size issue

    By [Et...] , December 27, 2024
    • 3 replies
    • 1k views
    • 
    • [Ja...]
    • February 18

17. Accuracy of T-SCAN HAWAK 2

    By [al...] , February 12
    • 4 replies
    • 721 views
    • 
    • [al...]
    • February 13

18. Triggering Scan Directly in ZEISS HAWK2 ADD-ON

    By [Yu...] , February 10
    • 0 replies
    • 409 views
    • 
    • [Yu...]
    • February 10

19. Free ZEISS INSPECT Optical 3D

    By [Je...] , January 14
    • 2 replies
    • 914 views
    • 
    • [Mi...]
    • February 4

20. Error MPROJ-0040 T-Scan hawk 2

    By [Zu...] , January 25, 2024
    • 4 replies
    • 10.1k views
    • 
    • [Mi...]
    • February 4

21. Is it possible to extract raw CT scan data from a GOM Inspect file?

    By [Fi...] , January 22, 2024
    • 1 reply
    • 1.6k views
    • 
    • [Ra...]
    • January 30

22. Use of Track Ball mouse instead of Logitech R400 remote control for ATOS scan

    By [Sh...] , February 20, 2024
    • 1 reply
    • 1.2k views
    • 
    • [Ra...]
    • January 30

23. Save scan images

    By [Ri...] , March 13, 2024
    • 1 reply
    • 5.8k views
    • 
    • [Ra...]
    • January 30

24. Changing to smaller Measuring Volumes (MV)

    By [Iv...] , September 20, 2024
    • 1 reply
    • 955 views
    • 
    • [Ra...]
    • January 30

25. Ausrichtung der Messungen

    By [Ja...] , September 13, 2024
    • 6 replies
    • 1.6k views
    • 
    • [Ja...]
    • January 29