Optical 3D

192 topics in this forum

1. Broken HDD _ Re-install measurement and scan environment

   By [Fl...] , July 23
   • 2 replies
   • 305 views
   • 
   • [Na...]
   • July 28

2. Accuracy of T-SCAN HAWAK 2

   By [al...] , February 12
   • 5 replies
   • 914 views
   • 
   • [Ce...]
   • July 23

3. Error MFG-0011

   By [Mi...] , June 16
   • 1 reply
   • 525 views
   • 
   • [Ja...]
   • June 20

4. Low quality of triple scan points error

   By [Sh...] , May 7
   • 9 replies
   • 998 views
   • 
   • [Je...]
   • June 16

5. How to activate license and start INSPECT Optical 3D on offline PC ?

   By [Ka...] , May 28
   • 1 reply
   • 408 views
   • 
   • [Je...]
   • June 12

6. Hardware Initialization failed

   By [ra...] , May 27
   • 0 replies
   • 428 views
   • 
   • [ra...]
   • May 27

7. Mit welchen Messsystemen kann Inspect messen

   By [Ax...] , April 4
   • 2 replies
   • 933 views
   • 
   • [Ax...]
   • May 15

8. Zeiss Comet L3D 5M - installation issue - Gig E vision board not found

   By [Lu...] , March 26, 2024
   • 4 replies
   • 2.1k views
   • 
   • [Ab...]
   • April 22

9. T-hawk 2 scanner will not initialize scan lines

   By [mi...] , December 4, 2024
   • 1 reply
   • 1.2k views
   • 
   • [Ky...]
   • April 16

10. Losing detail on vane leading and trailing edges after polygonization

    By [Mi...] , April 11
    • 1 reply
    • 1.5k views
    • 
    • [Ch...]
    • April 15

11. T-Hawk 2 not supported by Zeiss Inspect 2025?

    By [Se...] , April 9
    • 1 reply
    • 618 views
    • 
    • [Na...]
    • April 9

12. Reliability of Hyperscale calibration with ATOS Q

    By [Yu...] , April 9
    • 0 replies
    • 524 views
    • 
    • [Yu...]
    • April 9

13. Inspect Correlate 2023 - Getting extremely slow when adding multiple measurement series

    By [Ch...] , April 3
    • 1 reply
    • 503 views
    • 
    • [Ch...]
    • April 3

14. Notebook for data acquisition

    By [Ma...] , September 26, 2024
    • 3 replies
    • 1.9k views
    • 
    • [Ky...]
    • April 2

15. Best way to measure threaded holes?

    By [da...] , March 14
    • 2 replies
    • 2.1k views
    • 
    • [da...]
    • March 21

16. Compact Scan Error 1282

    By [St...] , September 3, 2021
    • 9 replies
    • 6.7k views
    • 
    • [Ja...]
    • March 14

17. Need help PMI - import to Inspect optical 3D. - show invalid or not support.

    By [Yo...] , February 28
    • 1 reply
    • 476 views
    • 
    • [na...]
    • March 3

18. ATOS I 2M 350 scanning size issue

    By [Et...] , December 27, 2024
    • 3 replies
    • 1.1k views
    • 
    • [Ja...]
    • February 18

19. Triggering Scan Directly in ZEISS HAWK2 ADD-ON

    By [Yu...] , February 10
    • 0 replies
    • 499 views
    • 
    • [Yu...]
    • February 10

20. Free ZEISS INSPECT Optical 3D

    By [Je...] , January 14
    • 2 replies
    • 1.1k views
    • 
    • [Mi...]
    • February 4

21. Error MPROJ-0040 T-Scan hawk 2

    By [Zu...] , January 25, 2024
    • 4 replies
    • 10.3k views
    • 
    • [Mi...]
    • February 4

22. Is it possible to extract raw CT scan data from a GOM Inspect file?

    By [Fi...] , January 22, 2024
    • 1 reply
    • 1.8k views
    • 
    • [Ra...]
    • January 30

23. Use of Track Ball mouse instead of Logitech R400 remote control for ATOS scan

    By [Sh...] , February 20, 2024
    • 1 reply
    • 1.3k views
    • 
    • [Ra...]
    • January 30

24. Save scan images

    By [Ri...] , March 13, 2024
    • 1 reply
    • 5.9k views
    • 
    • [Ra...]
    • January 30

25. Changing to smaller Measuring Volumes (MV)

    By [Iv...] , September 20, 2024
    • 1 reply
    • 1.1k views
    • 
    • [Ra...]
    • January 30