General Discussion

295 topics in this forum

1. Scanbox 5120 Fixture Location

   By [Ja...] , January 19
   • 1 reply
   • 307 views
   • 
   • [Na...]
   • January 20

2. What's up with the New XXT base plate, it doesn't fit

   By [Ro...] , January 18
   • 2 replies
   • 373 views
   • 
   • [No...]
   • January 19

3. Cylinder element acquisition

   By [Fe...] , January 7
   • 5 replies
   • 629 views
   • 
   • [Fe...]
   • January 14

4. Rundlaufauswertung Welle

   By [Fi...] , January 13
   • 6 replies
   • 627 views
   • 
   • [Da...]
   • January 14

5. Undercut Approach from Clearance Z+

   By [Br...] , January 8
   • 1 reply
   • 349 views
   • 
   • [Cl...]
   • January 8

6. Frequency of viewing probes under a microscope

   By [An...] , December 11, 2025
   • 7 replies
   • 5.4k views
   • 
   • [Jo...]
   • January 6

7. Homeing a Contura

   By [Rh...] , January 6
   • 1 reply
   • 346 views
   • 
   • [Du...]
   • January 6

8. GD and T General question

   By [Ma...] , December 10, 2025
   • 7 replies
   • 851 views
   • 
   • [To...]
   • December 31, 2025

9. Hone relief 12" deep-what to use

   By [Li...] , October 15, 2025
   • 3 replies
   • 661 views
   • 
   • [Wo...]
   • December 23, 2025

10. Minimum System Requirements for Correlate

    By [Ch...] , October 31, 2025
    • 1 reply
    • 1.9k views
    • 
    • [Mo...]
    • December 18, 2025

11. Coordinates for excel

    By [Bl...] , December 10, 2025
    • 8 replies
    • 919 views
    • 
    • [Bl...]
    • December 11, 2025

12. Coordinate System Placement: Where (or how)

    By [Ra...] , December 10, 2025
    • 6 replies
    • 901 views
    • 
    • [Ri...]
    • December 11, 2025

13. Batch file help. Creating folders with sub folders. 1 2

    By [Ri...] , October 15, 2025
    • 29 replies
    • 2.8k views
    • 
    • [Ri...]
    • December 4, 2025

14. TRUE Sphere

    By [Al...] , December 2, 2025
    • 3 replies
    • 1.5k views
    • 
    • [Jo...]
    • December 4, 2025

15. CMM serviced 2 days ago

    By [Al...] , September 29, 2025
    • 12 replies
    • 1.9k views
    • 
    • [Pa...]
    • November 29, 2025

16. Contura with Calypso and Rotary Table

    By [To...] , November 19, 2025
    • 1 reply
    • 473 views
    • 
    • [Pa...]
    • November 29, 2025

17. Stylus Accuracy

    By [Jo...] , November 5, 2025
    • 7 replies
    • 1.1k views
    • 
    • [Iv...]
    • November 25, 2025

18. Programming Help

    By [Da...] , October 30, 2025
    • 4 replies
    • 858 views
    • 
    • [Pa...]
    • November 23, 2025

19. ZEISS SPECTRUM CMM / M3 THREADS XXT

    By [Ra...] , November 13, 2025
    • 4 replies
    • 728 views
    • 
    • [Ri...]
    • November 20, 2025

20. List of Measurement plans used last

    By [Ch...] , November 19, 2025
    • 8 replies
    • 777 views
    • 
    • [Ri...]
    • November 20, 2025

21. MEASURMENT PLAN INFO IN PI WEB HEADER

    By [gr...] , November 10, 2025
    • 7 replies
    • 709 views
    • 
    • [gr...]
    • November 17, 2025

22. Hilfe bei der korrekten Definition der Ausrichtung von Bezug C

    By [St...] , November 12, 2025
    • 5 replies
    • 654 views
    • 
    • [Ma...]
    • November 14, 2025

23. position reported one with MMC and another without

    By [Ni...] , September 17, 2025
    • 3 replies
    • 690 views
    • 
    • [Ma...]
    • November 13, 2025

24. Mal ein Lob an GOM/Zeiss

    By [Ax...] , October 29, 2025
    • 2 replies
    • 830 views
    • 
    • [Th...]
    • November 11, 2025

25. Zeiss Inspect and polyworks inspect

    By [Je...] , November 10, 2025
    • 0 replies
    • 455 views
    • 
    • [Je...]
    • November 10, 2025