3D Inspection & Mesh Editing​

829 topics in this forum

1. Erste Erfahrungen mit dem Aesub Referenzpunktnetz / First experience with the Aesub Target net

   By [St...] , October 25, 2023
   • 6 replies
   • 1.8k views
   • 
   • [Na...]
   • November 1, 2023

2. Replacing a higher resolution CAD model

   By [Ti...] , October 24, 2023
   • 3 replies
   • 14.9k views
   • 
   • [No...]
   • October 31, 2023

3. accessing reference points and pixels

   By [Ro...] , October 23, 2023
   • 0 replies
   • 2.6k views
   • 
   • [Ro...]
   • October 23, 2023

4. How to check concentricity in this case ?

   By [Vi...] , October 19, 2023
   • 2 replies
   • 20.2k views
   • 
   • [Vi...]
   • October 20, 2023

5. Surface profile representation

   By [Ja...] , October 12, 2023
   • 8 replies
   • 13.7k views
   • 
   • [Ja...]
   • October 20, 2023

6. Measure length of a section curve

   By [Ry...] , October 17, 2023
   • 3 replies
   • 3k views
   • 
   • [Ry...]
   • October 17, 2023

7. Calculating volume from surface comparison

   By [Je...] , January 28, 2021
   • 7 replies
   • 3.9k views
   • 
   • [al...]
   • October 17, 2023

8. Durchnittswert eines Ausdrucks über alle Stufen berechnen:

   By [Ma...] , October 6, 2023
   • 2 replies
   • 1.2k views
   • 
   • [Ma...]
   • October 17, 2023

9. Need to reduce STL file size without compromising data quality.

   By [Ma...] , September 8, 2023
   • 1 reply
   • 2.2k views
   • 
   • [Na...]
   • October 16, 2023

10. Best way to measure deviation between two 3D orthodontic brackets ?

    By [Se...] , September 14, 2023
    • 1 reply
    • 1.7k views
    • 
    • [Na...]
    • October 16, 2023

11. XYZ DATUM .CSV EXPORT

    By [Ba...] , October 16, 2023
    • 1 reply
    • 7.5k views
    • 
    • [Na...]
    • October 16, 2023

12. XYZ DATUM .CSV EXPORT

    By [Ba...] , October 16, 2023
    • 1 reply
    • 11k views
    • 
    • [Ba...]
    • October 16, 2023

13. Auto line and the orange line

    By [Ti...] , October 11, 2023
    • 1 reply
    • 5.7k views
    • 
    • [Ch...]
    • October 12, 2023

14. Unterschiedliche Ergebnisse zw. Flächenprofil und Max. Abweichungsfähnchen

    By [An...] , October 10, 2023
    • 1 reply
    • 1.1k views
    • 
    • [Ch...]
    • October 11, 2023

15. Bei Istnetz aus CAD: Bezugssystem weicht ab

    By [No...] , October 9, 2023
    • 4 replies
    • 3.4k views
    • 
    • [No...]
    • October 10, 2023

16. Section cuts actual are not inheriting the current alignment

    By [Ti...] , July 17, 2023
    • 10 replies
    • 3.1k views
    • 
    • [Be...]
    • October 4, 2023

17. Measuring radius of a curve

    By [Ke...] , May 10, 2023
    • 3 replies
    • 4.6k views
    • 
    • [Ha...]
    • October 2, 2023

18. Oberflächenabgleich zwischen CAD-Modell und Punktewolke

    By [Aa...] , September 27, 2023
    • 1 reply
    • 2.2k views
    • 
    • [Be...]
    • September 29, 2023

19. Surface Comparison On Actual without & with CAD

    By [Jo...] , September 29, 2023
    • 1 reply
    • 1.7k views
    • 
    • [Be...]
    • September 29, 2023

20. How to simultaneously compare multiple meshes against the original CAD

    By [Ko...] , September 27, 2023
    • 2 replies
    • 2.2k views
    • 
    • [Ko...]
    • September 28, 2023

21. Best fit by selected cad surfaces only

    By [Jo...] , September 27, 2023
    • 2 replies
    • 2.4k views
    • 
    • [Jo...]
    • September 27, 2023

22. Flatness control in a given zone of the model

    By [Pi...] , January 4, 2022
    • 4 replies
    • 3k views
    • 
    • [Ti...]
    • September 26, 2023

23. Position Schnittkreis zu Schnittpunkt

    By [Fr...] , September 25, 2023
    • 1 reply
    • 2k views
    • 
    • [Be...]
    • September 26, 2023

24. "dN" - what means?

    By [Wo...] , September 22, 2023
    • 1 reply
    • 16.3k views
    • 
    • [Be...]
    • September 25, 2023

25. Inversion of dN

    By [Kr...] , August 15, 2022
    • 14 replies
    • 10.7k views
    • 
    • [Be...]
    • September 25, 2023