3D Inspection & Mesh Editing​

808 topics in this forum

1. Deleting small objects

   By [Ry...] , November 6, 2023
   • 4 replies
   • 4.8k views
   • 
   • [Na...]
   • November 6, 2023

2. Maß wird nicht in Tabelle angezeigt

   By [No...] , October 31, 2023
   • 4 replies
   • 9.7k views
   • 
   • [No...]
   • November 6, 2023

3. Measure alignment between two axis /center lines of cylinders

   By [Lu...] , November 4, 2023
   • 2 replies
   • 3k views
   • 
   • [Be...]
   • November 6, 2023

4. Report pages and tagging reports

   By [Ti...] , October 31, 2023
   • 2 replies
   • 4.3k views
   • 
   • [Ti...]
   • November 1, 2023

5. Erste Erfahrungen mit dem Aesub Referenzpunktnetz / First experience with the Aesub Target net

   By [St...] , October 25, 2023
   • 6 replies
   • 1.6k views
   • 
   • [Na...]
   • November 1, 2023

6. Replacing a higher resolution CAD model

   By [Ti...] , October 24, 2023
   • 3 replies
   • 14.7k views
   • 
   • [No...]
   • October 31, 2023

7. accessing reference points and pixels

   By [Ro...] , October 23, 2023
   • 0 replies
   • 2.4k views
   • 
   • [Ro...]
   • October 23, 2023

8. How to check concentricity in this case ?

   By [Vi...] , October 19, 2023
   • 2 replies
   • 20k views
   • 
   • [Vi...]
   • October 20, 2023

9. Surface profile representation

   By [Ja...] , October 12, 2023
   • 8 replies
   • 13.3k views
   • 
   • [Ja...]
   • October 20, 2023

10. Measure length of a section curve

    By [Ry...] , October 17, 2023
    • 3 replies
    • 2.8k views
    • 
    • [Ry...]
    • October 17, 2023

11. Calculating volume from surface comparison

    By [Je...] , January 28, 2021
    • 7 replies
    • 3.6k views
    • 
    • [al...]
    • October 17, 2023

12. Durchnittswert eines Ausdrucks über alle Stufen berechnen:

    By [Ma...] , October 6, 2023
    • 2 replies
    • 1.1k views
    • 
    • [Ma...]
    • October 17, 2023

13. Need to reduce STL file size without compromising data quality.

    By [Ma...] , September 8, 2023
    • 1 reply
    • 2k views
    • 
    • [Na...]
    • October 16, 2023

14. Best way to measure deviation between two 3D orthodontic brackets ?

    By [Se...] , September 14, 2023
    • 1 reply
    • 1.5k views
    • 
    • [Na...]
    • October 16, 2023

15. XYZ DATUM .CSV EXPORT

    By [Ba...] , October 16, 2023
    • 1 reply
    • 7.4k views
    • 
    • [Na...]
    • October 16, 2023

16. XYZ DATUM .CSV EXPORT

    By [Ba...] , October 16, 2023
    • 1 reply
    • 10.9k views
    • 
    • [Ba...]
    • October 16, 2023

17. Auto line and the orange line

    By [Ti...] , October 11, 2023
    • 1 reply
    • 5.6k views
    • 
    • [Ch...]
    • October 12, 2023

18. Unterschiedliche Ergebnisse zw. Flächenprofil und Max. Abweichungsfähnchen

    By [An...] , October 10, 2023
    • 1 reply
    • 929 views
    • 
    • [Ch...]
    • October 11, 2023

19. Bei Istnetz aus CAD: Bezugssystem weicht ab

    By [No...] , October 9, 2023
    • 4 replies
    • 3.2k views
    • 
    • [No...]
    • October 10, 2023

20. Section cuts actual are not inheriting the current alignment

    By [Ti...] , July 17, 2023
    • 10 replies
    • 2.7k views
    • 
    • [Be...]
    • October 4, 2023

21. Measuring radius of a curve

    By [Ke...] , May 10, 2023
    • 3 replies
    • 4.4k views
    • 
    • [Ha...]
    • October 2, 2023

22. Oberflächenabgleich zwischen CAD-Modell und Punktewolke

    By [Aa...] , September 27, 2023
    • 1 reply
    • 1.9k views
    • 
    • [Be...]
    • September 29, 2023

23. Surface Comparison On Actual without & with CAD

    By [Jo...] , September 29, 2023
    • 1 reply
    • 1.5k views
    • 
    • [Be...]
    • September 29, 2023

24. How to simultaneously compare multiple meshes against the original CAD

    By [Ko...] , September 27, 2023
    • 2 replies
    • 2k views
    • 
    • [Ko...]
    • September 28, 2023

25. Best fit by selected cad surfaces only

    By [Jo...] , September 27, 2023
    • 2 replies
    • 2.3k views
    • 
    • [Jo...]
    • September 27, 2023