General

8148 topics in this forum

1. Contura XXT storage and pickup problem from rack

   By [Ma...] , May 5
   • 3 replies
   • 430 views
   • 
   • [Ma...]
   • May 7

2. Rotary table qualification

   By [Dr...] , May 4
   • 1 reply
   • 409 views
   • 
   • [Ca...]
   • May 6

3. Messelement Fläche ersetzen

   By [Ba...] , May 5
   • 2 replies
   • 512 views
   • 
   • [Ch...]
   • May 6

4. Torus issue in Calypso 2025

   By [Jo...] , November 19, 2025
   • 17 replies
   • 3.2k views
   • 
   • [Ch...]
   • May 6

5. Loop on second alignment

   By [Lu...] , May 5
   • 7 replies
   • 821 views
   • 
   • [De...]
   • May 6

6. How to report intersection point (cylinder and cone)

   By [K...] , May 5
   • 3 replies
   • 447 views
   • 
   • [Ri...]
   • May 6

7. How do I change this dang order number in Piweb!?

   By [Jo...] , April 24
   • 2 replies
   • 474 views
   • 
   • [An...]
   • May 5

8. How to disable shape plot report?

   By [Ma...] , April 24
   • 3 replies
   • 563 views
   • 
   • [An...]
   • May 5

9. Form oder Rundheit ohne Toleranz

   By [Ro...] , May 4
   • 1 reply
   • 354 views
   • 
   • [Jö...]
   • May 4

10. Qdas Export Problem mit 8.0.1203

    By [Ma...] , April 28
    • 8 replies
    • 697 views
    • 
    • [No...]
    • May 4

11. 4 Datum Pads different heights

    By [Ro...] , April 29
    • 6 replies
    • 758 views
    • 
    • [Al...]
    • May 1

12. Composite Position Tolerance

    By [Mi...] , November 2, 2022
    • 10 replies
    • 3k views
    • 
    • [De...]
    • May 1

13. Min Max Flatness Plot

    By [Ra...] , May 1
    • 3 replies
    • 482 views
    • 
    • [Je...]
    • May 1

14. CALYPSO Symmetry Plane / Datum C Showing Y Offset on Slot (Understanding Feature Location)

    By [Sh...] , April 29
    • 10 replies
    • 1k views
    • 
    • [Sh...]
    • May 1

15. probe crash and actual pnt issues- Why tho!

    By [Jo...] , April 14
    • 5 replies
    • 622 views
    • 
    • [Jo...]
    • May 1

16. Pre-run Stylus Qualification Check failing even though the stylus system qualified within limits

    By [Er...] , April 28
    • 1 reply
    • 473 views
    • 
    • [Za...]
    • April 30

17. CMM run per day.

    By [Lu...] , April 21
    • 12 replies
    • 1.2k views
    • 
    • [Ri...]
    • April 30

18. GDT Profile, FF vs Feature & Best Fit

    By [Ze...] , April 30
    • 4 replies
    • 860 views
    • 
    • [Ri...]
    • April 30

19. No connection made with CMM

    By [Ja...] , April 29
    • 9 replies
    • 659 views
    • 
    • [Za...]
    • April 30

20. Where are the internal temperature sensors on a Contura?

    By [Jo...] , April 29
    • 0 replies
    • 422 views
    • 
    • [Jo...]
    • April 29

21. Risultati calibrazione tastatori

    By [Mi...] , April 29
    • 1 reply
    • 338 views
    • 
    • [Ma...]
    • April 29

22. Clocking to the outside of a hole on round part

    By [Ma...] , April 26
    • 8 replies
    • 793 views
    • 
    • [Ma...]
    • April 28

23. You had me at charcoal. 1 2

    By [Je...] , October 2, 2025
    • 35 replies
    • 5.3k views
    • 
    • [Ch...]
    • April 28

24. "33 Collision" While Qualifying Probe

    By [Fr...] , April 27
    • 7 replies
    • 753 views
    • 
    • [Fr...]
    • April 27

25. Calypso 8.0: Planner - Simulation

    By [Ri...] , February 10
    • 13 replies
    • 2.2k views
    • 
    • [Ro...]
    • April 27